Craig-RV8a
Member
Here's some information with regards to the RV nose gear, that was just posted. Check out the information on the links.
http://www.ntsb.gov/ntsb/brief.asp?ev_id=20051006X01588&key=1
http://www.ntsb.gov/ntsb/query.asp
http://www.ntsb.gov/publictn/2006/RV_Study.pdf
http://www.ntsb.gov/publictn/2006/RV_Photos.pdf
NTSB Identification: ANC05LA123.
The docket is stored in the Docket Management System (DMS). Please contact Records Management Division
14 CFR Part 91: General Aviation
Accident occurred Friday, August 12, 2005 in Palmer, AK
Probable Cause Approval Date: 6/27/2007
Aircraft: Brabandt RV-9A, registration: N63EB
Injuries: 1 Minor.
The commercial certificated pilot was landing a tricycle gear-equipped kit-built experimental airplane on a private airstrip that had an uneven dirt/gravel surface. During the landing roll, the nose landing gear began producing scuff marks on the runway surface that became progressively deeper. The nose gear strut and fork eventually dug into the runway, and the nose landing gear strut was bent aft. The airplane nosed over, and received structural damage to the fuselage, left elevator, left wing, rudder, and vertical stabilizer. An exam of the runway revealed surface undulations in the area where the nose wheel fork assembly began to scuff the tops of the undulations, producing slight gouge marks that increased in depth and ended where the nose fork dug into the ground. There were no skidding signatures or evidence that the main landing wheel tires were locked before the airplane nosed over. An exam of the airplane revealed that the nose gear strut was bent aft and upward from its normal geometry. The nose fork assembly is comprised of a metal swiveling housing block, attached to the lower end of the threaded strut by a nut. The bottom edge of the threaded nose fork strut is about 4 inches from the ground. A teardrop-shaped fiberglass wheel pant enclosed the accident airplane's nose fork assembly and upper portion of the nose wheel and tire. The distance from the bottom of the wheel pant and ground is about 2 and 7/16 inches. Staff examined data for 18 recent accidents and one incident in which Vans Aircraft series RV-6A, RV-7A, RV-8A, or RV-9A airplanes have become inverted during landing. Several involved hard touchdowns, bounced landings (six), or landing in a slip. Several others involved off-field landings in rough terrain, hitting a ditch, or going down an embankment. Four of the accidents and one incident involved a touchdown and the start of a rollout on an unpaved runway, followed by the nose gear folding back. The airplanes would then slide for varying distances before nosing over. Staff also examined data for four additional incidents in which the nose gear collapsed during taxi but the airplane did not nose over. These nine accidents and incidents occurred on various unpaved surfaces including gravel, turf, soft turf, hard surface with "washboard" bumps, and slight depressions, and they all involved the nose gear strut and fork digging into the ground and the nose gear bending aft. The kit manufacturer posted a letter on their website stating that their review of NTSB accident reports pointed to pilot proficiency as the most significant factor. The letter said the company has produced a lighter weight leg/fork combination, with increased clearance between the nose strut axle.
The NTSB's Structures Study is available at the following address: http://www.ntsb.gov/publictn/2006/RV_Study.pdf . The NTSB's Photos and Data report that provides details on all of the RV nose-over accidents and incidents can be found at the following URL address: http://www.ntsb.gov/publictn/2006/RV_Photos.pdf.
The National Transportation Safety Board determines the probable cause(s) of this accident as follows:
The loss of nose gear strut/fork-to-ground clearance that led to the collapse of the nose gear strut and nose-over during the landing roll. Factors contributing to the accident were an uneven dirt/gravel surface runway.
http://www.ntsb.gov/ntsb/brief.asp?ev_id=20051006X01588&key=1
http://www.ntsb.gov/ntsb/query.asp
http://www.ntsb.gov/publictn/2006/RV_Study.pdf
http://www.ntsb.gov/publictn/2006/RV_Photos.pdf
NTSB Identification: ANC05LA123.
The docket is stored in the Docket Management System (DMS). Please contact Records Management Division
14 CFR Part 91: General Aviation
Accident occurred Friday, August 12, 2005 in Palmer, AK
Probable Cause Approval Date: 6/27/2007
Aircraft: Brabandt RV-9A, registration: N63EB
Injuries: 1 Minor.
The commercial certificated pilot was landing a tricycle gear-equipped kit-built experimental airplane on a private airstrip that had an uneven dirt/gravel surface. During the landing roll, the nose landing gear began producing scuff marks on the runway surface that became progressively deeper. The nose gear strut and fork eventually dug into the runway, and the nose landing gear strut was bent aft. The airplane nosed over, and received structural damage to the fuselage, left elevator, left wing, rudder, and vertical stabilizer. An exam of the runway revealed surface undulations in the area where the nose wheel fork assembly began to scuff the tops of the undulations, producing slight gouge marks that increased in depth and ended where the nose fork dug into the ground. There were no skidding signatures or evidence that the main landing wheel tires were locked before the airplane nosed over. An exam of the airplane revealed that the nose gear strut was bent aft and upward from its normal geometry. The nose fork assembly is comprised of a metal swiveling housing block, attached to the lower end of the threaded strut by a nut. The bottom edge of the threaded nose fork strut is about 4 inches from the ground. A teardrop-shaped fiberglass wheel pant enclosed the accident airplane's nose fork assembly and upper portion of the nose wheel and tire. The distance from the bottom of the wheel pant and ground is about 2 and 7/16 inches. Staff examined data for 18 recent accidents and one incident in which Vans Aircraft series RV-6A, RV-7A, RV-8A, or RV-9A airplanes have become inverted during landing. Several involved hard touchdowns, bounced landings (six), or landing in a slip. Several others involved off-field landings in rough terrain, hitting a ditch, or going down an embankment. Four of the accidents and one incident involved a touchdown and the start of a rollout on an unpaved runway, followed by the nose gear folding back. The airplanes would then slide for varying distances before nosing over. Staff also examined data for four additional incidents in which the nose gear collapsed during taxi but the airplane did not nose over. These nine accidents and incidents occurred on various unpaved surfaces including gravel, turf, soft turf, hard surface with "washboard" bumps, and slight depressions, and they all involved the nose gear strut and fork digging into the ground and the nose gear bending aft. The kit manufacturer posted a letter on their website stating that their review of NTSB accident reports pointed to pilot proficiency as the most significant factor. The letter said the company has produced a lighter weight leg/fork combination, with increased clearance between the nose strut axle.
The NTSB's Structures Study is available at the following address: http://www.ntsb.gov/publictn/2006/RV_Study.pdf . The NTSB's Photos and Data report that provides details on all of the RV nose-over accidents and incidents can be found at the following URL address: http://www.ntsb.gov/publictn/2006/RV_Photos.pdf.
The National Transportation Safety Board determines the probable cause(s) of this accident as follows:
The loss of nose gear strut/fork-to-ground clearance that led to the collapse of the nose gear strut and nose-over during the landing roll. Factors contributing to the accident were an uneven dirt/gravel surface runway.