VAF Forums

VAF Forums (https://vansairforce.net/community/index.php)
-   My RV Build Project (https://vansairforce.net/community/forumdisplay.php?f=108)
-   -   My RV9A (https://vansairforce.net/community/showthread.php?t=193326)

Vlad 10-05-2021 05:29 PM

Good job at nice pace Jared! What's the timing on the fuselage?

Jslow2 10-05-2021 05:39 PM

Quote:

Originally Posted by Vlad (Post 1560041)
Good job at nice pace Jared! What's the timing on the fuselage?

Well an Ireland trip is kinda putting the finances for that on hold lol.

Hopefully get it april/May

Jslow2 10-06-2021 12:21 PM

2 Attachment(s)
First rib in.

Jslow2 10-07-2021 11:42 PM

More ribs done
 
2 Attachment(s)
Got a few more ribs riveted on today, but had to go to work before finishing. Dinged the spar with the bucking bar, made a cover out of cardboard to protect it.

Jslow2 10-19-2021 08:07 PM

More wing work
 
3 Attachment(s)
Initial left wing assembly.

Jslow2 11-10-2021 01:22 PM

Mistake
 
1 Attachment(s)
Maddie another boo boo, this one more serious...

Jslow2 12-13-2021 07:54 AM

1 Attachment(s)
Since lead times are long, decided to play around with solidworks.

Jslow2 12-13-2021 12:32 PM

1 Attachment(s)
Poor hand placement lol

Vlad 12-13-2021 01:22 PM

Quote:

Originally Posted by Jslow2 (Post 1575136)
Poor hand placement lol

Solidworks causes this. Be careful :D

Jslow2 12-24-2021 03:13 PM

1 Attachment(s)
Merry Christmas to me

Jslow2 01-03-2022 12:52 PM

4 Attachment(s)
Fuel tank work.

PilotjohnS 01-03-2022 01:22 PM

Never enough
 
Quote:

Originally Posted by Jslow2 (Post 1579625)
Fuel tank work.

Seems like you can never have enough proseal.

Lastly, I was going to add a second fuel level sender in the outer rib. I got talked out of it, but I wish I had. A second sender will allow accurate fuel level through the whole range from Full to empty, if using a G3X or other computer fuel gauge.

Jslow2 01-03-2022 01:53 PM

No proseal on fittings yet, just put them in to see the clearance with the sealed nutplates and the fuel pickup.

Jslow2 01-10-2022 01:04 PM

More tank work.
 
3 Attachment(s)
Finished the ribs on the left tank, fabricated spacer for the Newton fuel cap since the hole in the skin is larger now.

Jslow2 02-08-2022 10:50 AM

Bubbles
 
1 Attachment(s)
Few bubbles

wcalvert 02-08-2022 07:38 PM

Wow, that's more than a few bubbles! and this is on pressure from a balloon? Can you locate the source as the bolt heads or seal around the sender plate or multiples locations? It's hard to tell from the photo.

Your test photo shows a couple of concerning places: The bolt heads are not bedded in sealant, the seam between the end bulkhead and tank skin doesn't show any sealant squeeze out, the edge of the sender plate has gaps without squeeze out.

I looked back at some of your previous photos to see if there are any obvious glaring issues. Question: what type of fastener is on the fuel side of the sender plate bolts? They look to be standing proud of the pro seal and not capped off by the sealant. Maybe it's a new kind of fastener, but that arrangement doesn't look familiar.

Any way you slice it, you'll need to do some serious sleuthing and figure out the source of that leak. Hopefully it becomes clear soon.

Cheers

Jslow2 05-19-2022 03:46 PM

2 Attachment(s)
Left aileron work.

Jslow2 05-19-2022 03:49 PM

3 Attachment(s)
Left flap in process


All times are GMT -6. The time now is 05:36 AM.