VansAirForceForums  
Home > VansAirForceForums

-POSTING RULES
-Advertise in here!
- Today's Posts | Insert Pics

Keep VAF Going
Donate methods

Point your
camera app here
to donate fast.

  #1  
Old 02-05-2022, 08:47 PM
Steve Crewdog's Avatar
Steve Crewdog Steve Crewdog is offline
 
Join Date: Mar 2019
Location: KBVS
Posts: 228
Default Wire lacing knots not holding

Hi all,

Spent today lacing a run of wires together, got to a section that involved a curve and the tyes would not hold, almost immediately came undone. Went back over some of the tyes on the straight portion and some held, some didn't. I went back to the curve I had been working, did a few more and paid very careful attention to what I was doing (in case I was tired and getting sloppy), and they still came undone. Wondering if I trimmed the ends too close, or I'm tyeing them too tight, or...???

I'm using Method 2 as shown on the Aeroelectric Connection website, with waxed lacing cord. http://www.aeroelectric.com/articles...able_lace.html


Anyone else ran into this?


TIA
__________________
SeaRey builder lurking to get ideas to make his plane better, and keep his build from stopping like a gear down landing in water.
Dues paid for 2022
http://seareybuild.blogspot.com/
Reply With Quote
  #2  
Old 02-05-2022, 09:01 PM
PilotjohnS PilotjohnS is online now
 
Join Date: Jan 2016
Location: Southwest
Posts: 2,239
Default Just me

I dont use this method.but if the square knot is loosening, make sure you are doing a square knot and not a granny knot. On a square knot, the two ends that cross should come from the same side of the loop. A granny lnot has the two ends that cross perpendicular and not from the same side of the loop. Lastly, you could try a second twist on the cross over.
__________________
John S

WARNING! Information presented in this post is my opinion. All users of info have sole responsibility for determining accuracy or suitability for their use.

Dues paid 2022, worth every penny

RV9A- Status:
98% done, 2% left to go
Structure done (less gear)
Electrical/Panel done
Firewall Forward 95% done
Fiberglass 90%
www.pilotjohnsrv9.blogspot.com
Reply With Quote
  #3  
Old 02-05-2022, 10:23 PM
Steve Crewdog's Avatar
Steve Crewdog Steve Crewdog is offline
 
Join Date: Mar 2019
Location: KBVS
Posts: 228
Default

I think you may be right, I looked at the failed knots and the main parts were still intact, leading me to believe that one piece of line was "slipping through" the knot. I was also thinking that I was accidentally tying 2 half hitches, which would leave one piece of lacing cord accidentally becoming a standing line, and allowing it to slip through.
__________________
SeaRey builder lurking to get ideas to make his plane better, and keep his build from stopping like a gear down landing in water.
Dues paid for 2022
http://seareybuild.blogspot.com/
Reply With Quote
  #4  
Old 02-06-2022, 05:06 AM
marchudson's Avatar
marchudson marchudson is offline
 
Join Date: Feb 2006
Location: East Texas
Posts: 211
Default

Page 11-63 of AC43.13 has some good examples of tying wire bundles. I also had to place an extra loop after tying the square knot because some of the ties showed signs of loosening.

https://www.faa.gov/documentlibrary/...-1b_w-chg1.pdf

If you want additional knot information. The Ashely book of knots is the bible of knot tying. https://archive.org/details/TheAshle.../n185/mode/2up.

We lived on a sailboat for a while and between that book and the live aboard community we learned a lot about tying knots.
__________________
Marc Hudson
Houston
RV-7 Sold
Reply With Quote
  #5  
Old 02-06-2022, 06:12 AM
bobnoffs bobnoffs is offline
 
Join Date: Jul 2012
Location: n. wi
Posts: 933
Default

it's been my experience that after securing something it takes 3 half hitches to make the knot slipproof. i don't even think about it anymore, just tie 3 half hitches.
__________________
Bob Noffs
n. wi.
dakota hawk/jab 3300 built and flying. sold 6/18.getting serious about the 12. in the hangar now as of 10/15/19
RV-12 kit as of 9/13
RV-12 airworthiness cert. 11/30/2021
Reply With Quote
  #6  
Old 02-06-2022, 06:20 AM
Mike Buckler Mike Buckler is offline
 
Join Date: Aug 2012
Location: Chatham Ont.
Posts: 47
Default

Easy video https://m.youtube.com/watch?v=CR3z5WZeHTw
Reply With Quote
  #7  
Old 02-06-2022, 06:54 AM
agirard7a's Avatar
agirard7a agirard7a is offline
 
Join Date: Aug 2009
Location: Newport, RI
Posts: 770
Default Whiping

From my sailing background, i have found this technique very easy and secure.
Only requires a three or four wraps. Very quick and easy. Dental floss works great in a pinch!

https://youtu.be/n2HFjSW37a8
__________________
Al Girard, Newport, RI
N339AG
RV-9

Last edited by agirard7a : 02-06-2022 at 07:01 AM.
Reply With Quote
  #8  
Old 02-06-2022, 07:33 AM
N804RV's Avatar
N804RV N804RV is offline
 
Join Date: May 2013
Location: Mount Vernon, Wa
Posts: 908
Default

I've never used "method 2" . I've always used "method" 1, even on the biggest wire bundles.

Also, what kind of lacing are you using? My favorite is the Nomex lacing that my former employer uses. But, it can be hard to find. If you're using lacing that doesn't cinch down and tends to want to 'spring' apart before you tie the square knot, try something different.

The wax lacing cord that Steinair sells is easy to make nice neat wire bundles. Because it is waxed, it will hold some tension while you're tying the knot, making for a nice tight bundle. However, you need to wear something to protect your fingers. I used to tape the 1st knuckles on my index fingers to prevent the waxed lacing from sawing into the skin.
__________________
Ken W.
Mount Vernon, WA
2022 VAF Supporter

Last edited by N804RV : 02-06-2022 at 07:37 AM.
Reply With Quote
  #9  
Old 02-06-2022, 08:17 AM
wirejock's Avatar
wirejock wirejock is offline
 
Join Date: Oct 2005
Location: Estes Park, CO
Posts: 5,230
Default Method 2

I use the second method. You can cut wire with it. Never comes loose, but does requie a "square knot". Practice on shoe laces. A square knot will lay flat as tied. A "Granny" will rotate 90 degrees after releasing. Right over left, Left over right or whatever helps you remember.
__________________
Larry Larson
Estes Park, CO
wirejock at yahoo dot com
Donated 12/01/2021, plus a little extra.
RV-7A #73391, N511RV reserved (3,000+ hours)
Empennage, wings, fuse, finishing kit done. Working FWF
Disclaimer
I cannot be, nor will I be, held responsible if you try to do the same things I do and it does not work and/or causes you loss, injury, or even death in the process.
Reply With Quote
  #10  
Old 02-06-2022, 08:33 AM
rmarshall234 rmarshall234 is offline
 
Join Date: Jun 2008
Location: San Diego, CA
Posts: 355
Default

I've been using a Surgeon's knot like we do in the parachute rigging business along with waxed super tack nylon cord. Been working great for decades and I've never had a knot undue itself unless the waxed dried out or was subject to lots of abrasion. The "tail" should be trimmed to 1/4 inch.

https://en.wikipedia.org/wiki/Surgeon%27s_knot

http://www.paragear.com/skydiving/10...UPER-TACK-CORD
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 09:44 PM.


The VAFForums come to you courtesy Delta Romeo, LLC. By viewing and participating in them you agree to build your plane using standardized methods and practices and to fly it safely and in accordance with the laws governing the country you are located in.