VansAirForceForums  
Home > VansAirForceForums

-POSTING RULES
-Advertise in here!
- Today's Posts | Insert Pics

Keep VAF Going
Donate methods

Point your
camera app here
to donate fast.






VAF on Twitter:
@VansAirForceNet


Go Back   VAF Forums > Search Forums
Register FAQ Members List Calendar Search Today's Posts Mark Forums Read

Showing results 1 to 64 of 500
Search took 0.04 seconds.
Search: Posts Made By: PaulvS
Forum: RV-9/9A Today, 07:06 PM
Replies: 6
Views: 84
Posted By PaulvS
Those same side skins on my 6A were also not...

Those same side skins on my 6A were also not rolled enough and needed a fair bit of adjustment by clamping between some long boards and applying pressure. They went on and off several times to get...
Forum: RV Building Tips/Techniques Yesterday, 04:59 PM
Replies: 4
Views: 198
Posted By PaulvS
AOA port

That's what I've done on my 6A, put a pop rivet on the wing lower surface, ahead of the pitot tube. I got the location from a post on VAF by an RV-4 builder. All these models have the same wing...
Forum: RV General Discussion/News Yesterday, 03:47 PM
Replies: 9
Views: 474
Posted By PaulvS
The tubing that others have mentioned works well....

The tubing that others have mentioned works well. I use silicone rubber tubing as it is easy to slip on and doesn't leave a black mark like some other rubber can.

The shop head in the photo also...
Forum: RV-3 12-02-2022, 06:13 AM
Replies: 3
Views: 247
Posted By PaulvS
There is a service bulletin...

There is a service bulletin https://www.vansaircraft.com/service-information-and-revisions/sb-06-2-23/ for this that says for the builder to drill the hole in a standard AN nut.

Alternatively, you...
Forum: RV-7/7A 12-01-2022, 08:31 PM
Replies: 6
Views: 321
Posted By PaulvS
Ladder frame

There is a "better" way which is to use a sturdy and level ladder frame as used in the earlier kits, that is if you are prepared to go to the effort and expense of constructing one. I'm sure that...
Forum: VAF Classifieds (posts in here deleted after 30 days) 12-01-2022, 03:29 PM
Replies: 9
Views: 1,040
Posted By PaulvS
OTW

There's a couple now on the way to Australia, USPS shipping label created today, should get here in a month or so.
Forum: RV Ongoing Maintenance Issues 12-01-2022, 03:24 PM
Replies: 4
Views: 290
Posted By PaulvS
Shouldn't move too easily.

The aileron trim lever in ours does not move when the stick is moved. The friction is enough to hold it in position, but not so much friction that you can't adjust it by hand.
Forum: Engine Monitors 11-30-2022, 05:53 PM
Replies: 15
Views: 865
Posted By PaulvS
Wishing

Wouldn't it be nice if the G5 could display engine data from the GEA 24?!
Forum: RV-12/RV-12iS 11-30-2022, 04:40 PM
Replies: 6
Views: 732
Posted By PaulvS
A repair kit is available from Vans or...

A repair kit is available from Vans or elsewhere:
https://store.vansaircraft.com/matco-mc-4-brake-master-cylinder-rebuild-kit-brake-m-c-rbd4-repair.html
Forum: RV Building Tips/Techniques 11-29-2022, 04:23 PM
Replies: 8
Views: 544
Posted By PaulvS
If you want to use aluminum rather than ply or...

If you want to use aluminum rather than ply or plexi then commercial grade aluminum is quite cheap. I got a sheet of 5005 alloy 4' x 8' .040 for about $30. It is also available thicker .063 same as...
Forum: Engine Monitors 11-29-2022, 03:53 PM
Replies: 15
Views: 865
Posted By PaulvS
Rob you are not missing anything unfortunately,...

Rob you are not missing anything unfortunately, they are all expensive!

Another option may be a used Dynon EMS D10.

There is also Insight that was mentioned in couple of posts on VAF. Still, over...
Forum: VAF Classifieds (posts in here deleted after 30 days) 11-28-2022, 11:19 PM
Replies: 11
Views: 1,211
Posted By PaulvS
ACS

Also try Aircraft Spruce. Their website shows some items in stock or becoming available in Nov or Dec. If you place an order then you are at the front of the queue when they get stock. Note Dynon...
Forum: RV Building Tips/Techniques 11-28-2022, 10:14 PM
Replies: 7
Views: 354
Posted By PaulvS
If everything passes through the same hole then...

If everything passes through the same hole then that will mean less direct paths for at least some of the runs. Think about the origin and destination for each wire and what path will it follow....
Forum: RV-7/7A 11-27-2022, 09:08 PM
Replies: 10
Views: 557
Posted By PaulvS
+1 for this. It appears like the die in the...

+1 for this.

It appears like the die in the squeezer was for a 3/32 rivet even though the bag said 1/8, might've just got mixed up. The rivet head should sit nicely inside the depression in the die...
Forum: RV-8/8A 11-26-2022, 05:01 PM
Replies: 20
Views: 875
Posted By PaulvS
Why did you hate it? I already have the hole in...

Why did you hate it? I already have the hole in the aileron bracket during construction but a tech advisor saw it and suggested to instead split the pin in the middle.
Forum: RV General Discussion/News 11-26-2022, 03:16 PM
Replies: 10
Views: 1,573
Posted By PaulvS
I'm sure this is not the first time it's happened...

I'm sure this is not the first time it's happened to someone. I recall there is a comment in the construction manual about rounding off and tapering any sharp rubbing edges before inserting the...
Forum: My RV Build Project 11-24-2022, 08:53 PM
Replies: 101
Views: 44,819
Posted By PaulvS
More grins on the way

Thanks Dan, et al for PMs. What started out as 1 day job for SB 06-2-23 has blown out to be a much bigger job. I need to remind myself that one day this will all be worth it. :confused:

I made...
Forum: RV-8/8A 11-24-2022, 03:30 PM
Replies: 2
Views: 274
Posted By PaulvS
Testing

If you are going to blow into the pitot tube on the ground then you do know to put the Dynon (assuming it is a Skyview) into test mode, otherwise the calibration will be affected?

The problem may be...
Forum: RV-7/7A 11-23-2022, 05:52 PM
Replies: 9
Views: 382
Posted By PaulvS
Vans version

The attached image is of W822PP from the Vans website, try scaling it to print out at the correct size. The long dimension for the equivalent part on the RV-6 version is 9.125 inches but needs to be...
Forum: RV General Discussion/News 11-22-2022, 05:36 PM
Replies: 44
Views: 3,497
Posted By PaulvS
Discussion

Sounds like cheating and we were taught in kindergarten that nice people in society don't do that sort of thing. ;)

Separately, I have wondered about the WWII rare plane wreck that gets pulled up...
Forum: My RV Build Project 11-22-2022, 01:32 AM
Replies: 101
Views: 44,819
Posted By PaulvS
RV Grin

Sterling from Vans Support replied about the tank sealant issue and says that this is a very unusual problem and is usually confined to one or two spots, rather than the entire inside of the...
Forum: RV Building Tips/Techniques 11-21-2022, 06:34 PM
Replies: 58
Views: 11,832
Posted By PaulvS
Do you have any further info or background on why...

Do you have any further info or background on why the Proseal turns to goo if it is exposed to fuel vapor?

I (unfortunately) know that it can happen but it is totally bizarre that a product...
Forum: RV-8/8A 11-20-2022, 05:12 PM
Replies: 11
Views: 1,140
Posted By PaulvS
Here's how I support mine, including my weight...

Here's how I support mine, including my weight when crawling to work inside the tail cone, without any issues.
Forum: RV Building Tips/Techniques 11-20-2022, 04:51 PM
Replies: 58
Views: 11,832
Posted By PaulvS
Thanks for confirming the thickness of the Vans...

Thanks for confirming the thickness of the Vans T-412 cover plates. The rear baffle on the tank is .032 so they have made the plates one gauge thicker. The AD42H rivet spec states a minimum...
Forum: RV Building Tips/Techniques 11-20-2022, 12:37 AM
Replies: 58
Views: 11,832
Posted By PaulvS
Maybe someone who has purchased the access covers...

Maybe someone who has purchased the access covers from Vans will be able to 100% confirm the thickness?

In a couple of posts above, #32 and #35 above I think, there is a recommendation to put...
Forum: RV Building Tips/Techniques 11-19-2022, 11:06 PM
Replies: 58
Views: 11,832
Posted By PaulvS
Agreed, I would've probably used .040 unless...

Agreed, I would've probably used .040 unless someone had advised to use thicker for the covers. Also, Vans kit has 25 rivets per cover, which seems like a lot compared to the 12 screws in the access...
Forum: RV Building Tips/Techniques 11-19-2022, 04:51 PM
Replies: 58
Views: 11,832
Posted By PaulvS
Thanks Mike. Same thickness then as the access...

Thanks Mike. Same thickness then as the access plate for the fuel level sender but thicker than I actually expected for the repair kit covers.

Also found this old thread that has a load of useful...
Forum: My RV Build Project 11-18-2022, 08:15 PM
Replies: 101
Views: 44,819
Posted By PaulvS
Fuel tanks setback

I made a rather unpleasant discovery when I removed the tank inner access plates to carry out the Vans service bulletin that is to put safety wire on the B-nuts for the fuel pickup tubes.

I had...
Forum: RV Building Tips/Techniques 11-18-2022, 06:15 PM
Replies: 58
Views: 11,832
Posted By PaulvS
Cover plate thickness?

Getting ready to do this but may go for square or rectangular holes for improved access (I need to clean off and reseal everything inside because the original sealant has turned to goo).

Question:...
Forum: RV Ongoing Maintenance Issues 11-17-2022, 11:20 PM
Replies: 53
Views: 23,347
Posted By PaulvS
Sealant from Vans

I'm not sure what brand it was Walt and I no longer have the can but I bought it direct from Vans, in good faith, along with the pre-made fuel pickup tubes. It was shipped separately, some time after...
Forum: RV Ongoing Maintenance Issues 11-17-2022, 07:13 PM
Replies: 53
Views: 23,347
Posted By PaulvS
Proseal failure on unused tanks

Here's another data point, with a twist, for tank Proseal that has reverted to goo.

The tanks were built about 25 years ago and have been stored empty since then (very slow build RV-6A and tanks not...
Forum: RV Building Tips/Techniques 11-03-2022, 05:48 AM
Replies: 4
Views: 723
Posted By PaulvS
I didn't have any problems with dimpling the tail...

I didn't have any problems with dimpling the tail cone on my -6A that is also .040. The metal is slightly springy so that probably helps, but if it bothers you then it is structurally acceptable to...
Forum: Primers 11-02-2022, 07:58 AM
Replies: 6
Views: 692
Posted By PaulvS
There are subtle and distinct differences between...

There are subtle and distinct differences between brands and products so I think in the first instance I would check the technical data sheet for the specific primers that you are using. One data...
Forum: RV-12/RV-12iS 11-02-2022, 07:39 AM
Replies: 27
Views: 7,129
Posted By PaulvS
My guess is that the plane was parked outside...

My guess is that the plane was parked outside without a control lock on the stabilator and it banged up and down in the wind until the weight attach bracket fractured.
Forum: RV-7/7A 10-31-2022, 06:56 PM
Replies: 2,061
Views: 1,578,792
Posted By PaulvS
That's a Good Start, but not for the Faint of...

That's a Good Start, but not for the Faint of Heart.
Forum: RV General Discussion/News 10-30-2022, 09:04 PM
Replies: 20
Views: 1,768
Posted By PaulvS
The specifications via that link say not...

The specifications via that link say not recommended for use on acrylic and some plastics. The canopy is acrylic...
Forum: RV Building Tips/Techniques 10-30-2022, 07:36 AM
Replies: 3
Views: 408
Posted By PaulvS
The RV-6 construction sequence requires all 4...

The RV-6 construction sequence requires all 4 corners on the firewall to be drilled to enable the firewall to be attached to the jig. I drilled these holes undersize (1/4") to allow for final size...
Forum: RV-12/RV-12iS 10-29-2022, 06:15 PM
Replies: 5
Views: 752
Posted By PaulvS
On my -6A I retrofitted AOA and routed the tubing...

On my -6A I retrofitted AOA and routed the tubing via the wiring grommets in the ribs for the wing tip lighting. I don't know if that may be an option with the -12 wing?
Forum: RV-7/7A 10-27-2022, 10:20 PM
Replies: 20
Views: 1,910
Posted By PaulvS
I wondered about that accident in the Lance and...

I wondered about that accident in the Lance and whether the pilots could have done anything differently and survived, even though the root cause was no fault of theirs.

The attached pics are of the...
Forum: RV-7/7A 10-27-2022, 07:20 PM
Replies: 20
Views: 1,910
Posted By PaulvS
Thanks I saw that, for me shipping via UPS is...

Thanks I saw that, for me shipping via UPS is approx minimum $50 and with the current reduced exchange rate of $0.60 USD per $1.00 AUD that makes it $250. In daily living terms that's another chunk...
Forum: RV-7/7A 10-27-2022, 06:34 PM
Replies: 20
Views: 1,910
Posted By PaulvS
Firewall protection

I've had a closer look at the Vans aluminum hot air flapper valve box and I think it will be relatively easy to make it more robust in case of fire by replacing some of the aluminum components with...
Forum: RV General Discussion/News 10-25-2022, 10:28 PM
Replies: 21
Views: 1,473
Posted By PaulvS
Oh that's a bit of a bummer, I think the way I'd...

Oh that's a bit of a bummer, I think the way I'd approach it is firstly not to use heat for fear of cracking the plexi. (I have tried using heat to re-shape a polyester fairing and it wasn't very...
Forum: Painting your RV 10-25-2022, 10:00 PM
Replies: 34
Views: 2,233
Posted By PaulvS
A different nozzle/cap will also likely require a...

A different nozzle/cap will also likely require a different needle.

When I inquired about getting another size nozzle and needle for a (Star S770) gun the cost for the few parts was about the same...
Forum: RV General Discussion/News 10-25-2022, 05:46 AM
Replies: 11
Views: 1,027
Posted By PaulvS
Turf the stops!

The holes without using the depth stop look better, so there's your answer! Another technique is to extend a finger from the drill motor to help steady it and also to stop it from punching through...
Forum: Painting your RV 10-25-2022, 03:35 AM
Replies: 5
Views: 772
Posted By PaulvS
The spray paints that I'm using include etch...

The spray paints that I'm using include etch primer, epoxy primer and 2K polyurethane top coat. Any leftover paint or thinner from cleaning gets tipped into a slops bucket that is part filled with...
Forum: RV-7/7A 10-24-2022, 06:01 PM
Replies: 20
Views: 1,910
Posted By PaulvS
Hmmm... the cabin hot air flap box that I got...

Hmmm... the cabin hot air flap box that I got from Vans is aluminum. Is it junk? Replace it with the stainless version for another 0.2 AMU$? But then, the cowling is only epoxy, and the firewall...
Forum: RV-4 10-22-2022, 11:21 PM
Replies: 5
Views: 480
Posted By PaulvS
The Dynon website has servo installation guides...

The Dynon website has servo installation guides for download in the support section, have you found those?

Here is a link to the Trutrak install diagram for RV-4 roll. The servo footprint is...
Forum: Painting your RV 10-22-2022, 09:49 PM
Replies: 34
Views: 2,233
Posted By PaulvS
That seems like a nice gun and the online reviews...

That seems like a nice gun and the online reviews on the HF website are all positive.

How do you find having the regulator and filter mounted directly on the gun? Not too awkward? For mine, I hang...
Forum: Tools 10-22-2022, 08:12 PM
Replies: 20
Views: 1,508
Posted By PaulvS
I would say that a bandsaw is "nice to have" and...

I would say that a bandsaw is "nice to have" and a drill press is "essential".

My RV kit is an older version that requires more cutting, drilling and fabrication than the newer kits and I use the...
Forum: RV-9/9A 10-21-2022, 06:15 PM
Replies: 5
Views: 585
Posted By PaulvS
A chainsaw file, the smallest diameter 5/32", is...

A chainsaw file, the smallest diameter 5/32", is useful for a slot like that. The jeweler's files are a bit smaller but have finer teeth so can be a bit slow going and harder to control.

Sorry I...
Forum: RV General Discussion/News 10-21-2022, 08:47 AM
Replies: 7
Views: 1,069
Posted By PaulvS
Primer is primer

I found it to be very cost effective and not too much effort to apply an etch primer followed by 2-pack polyurethane for the cockpit. I used less than 1 litre PPG etch pro, easy to apply, dries...
Forum: RV-8/8A 10-20-2022, 01:49 AM
Replies: 8
Views: 922
Posted By PaulvS
Mel's suggested method has worked well for me,...

Mel's suggested method has worked well for me, using a work stand that has height adjustible legs. I've crawled in there quite a few (too many) times without any problems.
Forum: RV General Discussion/News 10-19-2022, 06:44 PM
Replies: 9
Views: 997
Posted By PaulvS
It was quite easy to level mine laterally by...

It was quite easy to level mine laterally by shimming under the feet of the sawhorse support. As you say though it is probably not that critical. The dihedral is already fixed.

It is very...
Forum: RV-7/7A 10-18-2022, 05:40 AM
Replies: 12
Views: 872
Posted By PaulvS
There should be a pilot hole in the skin, as per...

There should be a pilot hole in the skin, as per the one in the vertical cargo rib. Slip a rod e.g. 1/8 12" drill bit through both holes and make a cardboard template "washer" 1.5 inch outside...
Forum: RV-10 10-17-2022, 07:14 PM
Replies: 5
Views: 697
Posted By PaulvS
I agree it's worth completing the bend to see how...

I agree it's worth completing the bend to see how it looks once fitted, as the only concern would be cosmetic. Do you have a piece of scrap to practice on first? The 2024 is tricky to curve because...
Forum: RV-10 10-17-2022, 02:14 PM
Replies: 5
Views: 697
Posted By PaulvS
Crease

If you mean the break along the rivet line on the edge then it does look too much. It will be apparent on the finished painted plane and can detract cosmetically from the appearance. The bend should...
Forum: RV Building Tips/Techniques 10-16-2022, 06:56 PM
Replies: 13
Views: 1,274
Posted By PaulvS
Simple method

I use a small carpenters square that has an adjustable rule to mark a series of dots the required distance from the edge and then join them up with a 24 inch straight edge. Takes less than a minute...
Forum: RV Building Tips/Techniques 10-13-2022, 04:31 AM
Replies: 8
Views: 686
Posted By PaulvS
Check the plans - there should be a note that...

Check the plans - there should be a note that states to place washers between the firewall and the reservoir mounting bracket to avoid contact between the top of the reservoir and the firewall.
Forum: Trip Write-ups 10-12-2022, 08:33 PM
Replies: 14
Views: 2,277
Posted By PaulvS
Great writeup Dan, what a brave adventure! Does...

Great writeup Dan, what a brave adventure!
Does your ship have autopilot now or did you hand fly all the way?
Forum: Steam Gauges 10-12-2022, 07:12 PM
Replies: 5
Views: 1,178
Posted By PaulvS
Tube end

The order of assembly looks correct though I prefer a neat square cut with a sharp blade on the end of the tube. The end in the photo looks a bit ragged, it may be OK. Push the insert in as far as...
Forum: RV Building Tips/Techniques 10-12-2022, 06:39 PM
Replies: 8
Views: 686
Posted By PaulvS
+1 to wait until you have the reservoir before...

+1 to wait until you have the reservoir before drilling the holes. The Vans reservoir appears to be hand made so there may be some minor variation in the hole spacing.

I mounted it after riveting...
Forum: Probable Cause Documents Discussed 10-12-2022, 07:31 AM
Replies: 19
Views: 2,947
Posted By PaulvS
It is true that if the elevator was jammed then...

It is true that if the elevator was jammed then the trim tab would not have any effect on the elevator, however it would act as a mini elevator in its own right, operated in the opposite direction to...
Forum: Steam Gauges 10-11-2022, 03:40 PM
Replies: 5
Views: 1,178
Posted By PaulvS
The cap is to block off a line, so will probably...

The cap is to block off a line, so will probably not normally be needed, and the insert is to support the tube from collapsing when the nut is tightened. Dwg 36 for RV-7 has a diagram for how to...
Forum: RV Building Tips/Techniques 10-11-2022, 08:37 AM
Replies: 4
Views: 710
Posted By PaulvS
I make mistakes to appease the gods so they know...

I make mistakes to appease the gods so they know I'm an imperfect human. :)
Showing results 1 to 64 of 500

 
Forum Jump

All times are GMT -6. The time now is 10:18 PM.


The VAFForums come to you courtesy Delta Romeo, LLC. By viewing and participating in them you agree to build your plane using standardized methods and practices and to fly it safely and in accordance with the laws governing the country you are located in.